data sheet ligitek electronics co.,ltd. property of ligitek only round type led lamps doc. no : qw0905-LPG3333-PF rev. : a date : 13 - aug. - 2007 LPG3333-PF lead-free parts pb
60 100% note : 1.all dimension are in millimeter tolerance is 0.25mm unless otherwise noted. 2.specifications are subject to change without notice. directivity radiation -60 25% 100%75%50%25% 0 50%75% -30 0 30 ligitek electronics co.,ltd. property of ligitek only package dimensions page 1/5 part no. LPG3333-PF 0.5 typ 25.0min + - 2.54typ 1.0min 7.6 8.6 1.5max 5.0 5.9
note : 1.the forward voltage data did not including 0.1v testing tolerance. 2. the luminous intensity data did not including 15% testing tolerance. absolute maximum ratings at ta=25 i fp pd i f tstg t opr symbol typical electrical & optical characteristics (ta=25 ) power dissipation reverse current @5v storage temperature operating temperature parameter peak forward current duty 1/10@10khz forward current 100 -40 ~ +100 -40 ~ +85 ir10 ratings pg 120 30 mw a ma ma unit ligitek electronics co.,ltd. property of ligitek only page2/5 20 viewing angle 2 1/2 (deg) min. 30 20 min. 1.7 forward voltage @ ma(v) max. 2.6 peak wave length pnm 555 spectral halfwidth nm 30 typ. luminous intensity @10ma(mcd) 65 emitted green part no LPG3333-PF material gap lens color water clear part no. LPG3333-PF
fig.3 forward voltage vs. temperature fig.5 relative intensity vs. wavelength ambient temperature( ) r e l a t i v e i n t e n s i t y @ 2 0 m a wavelength (nm) f o r w a r d v o l t a g e @ 2 0 m a n o r m a l i z e @ 2 5 fig.4 relative intensity vs. temperature ambient temperature( ) r e l a t i v e i n t e n s i t y @ 2 0 m a n o r m a l i z e @ 2 5 typical electro-optical characteristics curve forward voltage(v) fig.1 forward current vs. forward voltage f o r w a r d c u r r e n t ( m a ) forward current(ma) fig.2 relative intensity vs. forward current r e l a t i v e i n t e n s i t y n o r m a l i z e @ 2 0 m a ligitek electronics co.,ltd. property of ligitek only 1.0 0.1 1.0 10 100 1000 1.0101001000 0.0 0.5 1.0 1.5 2.0 2.5 3.0 -40-200204060 1.0 1.1 1.2 500550600650 0.0 0.5 1.0 2.03.04.05.0 80100 0.8 0.9 -20 -40 40 20 080100 60 2.0 0.0 0.5 1.0 1.5 2.5 3.0 3.5 pg chip fig.6 directive radiation 4.0 page3/5 part no. LPG3333-PF
260 c3sec max 5 /sec max 260 120 temp( c) time(sec) 150 50 100 2 /sec max 25 0 preheat 0 60 seconds max page 4/5 ligitek electronics co.,ltd. property of ligitek only soldering condition(pb-free) 1.iron: soldering iron:30w max temperature 350 c max soldering time:3 seconds max(one time only) distance:2mm min(from solder joint to body) 2.wave soldering profile dip soldering preheat: 120 c max preheat time: 60seconds max ramp-up 2 c/sec(max) ramp-down:-5 c/sec(max) solder bath:260 c max dipping time:3 seconds max distance:2mm min(from solder joint to body) note:1.wave solder should not be made more than one time. 2.you can just only select one of the soldering conditions as above. part no. LPG3333-PF
page 5/5 reference standard mil-std-750: 1026 mil-std-883: 1005 jis c 7021: b-1 mil-std-883:1008 jis c 7021: b-10 jis c 7021: b-12 mil-std-202: 107d mil-std-750: 1051 mil-std-883: 1011 mil-std-202: 210a mil-std-750: 2031 jis c 7021: a-1 mil-std-202:103b jis c 7021: b-11 mil-std-202: 208d mil-std-750: 2026 mil-std-883: 2003 jis c 7021: a-2 test item operating life test reliability test: 1.under room temperature 2.if=20ma 3.t=1000 hrs (-24hrs, +72hrs) test condition high temperature storage test low temperature storage test thermal shock test solder resistance test high temperature high humidity test 1.t.sol=260 5 2.dwell time= 10 1sec. 1.ta=105 5 &-40 5 (10min) (10min) 2.total 10 cycles 1.ta=65 5 2.rh=90%~95% 3.t=240hrs 2hrs 1.ta=-40 5 2.t=1000 hrs (-24hrs, +72hrs) 1.ta=105 5 2.t=1000 hrs (-24hrs, +72hrs) solderability test 1.t.sol=230 5 2.dwell time=5 1sec this test intended to see soldering well performed or not. the purpose of this test is the resistance of the device under tropical for hours. this test intended to determine the thermal characteristic resistance of the device to sudden exposures at extreme changes in temperature when soldering the lead wire. the purpose of this is the resistance of the device to sudden extreme changes in high and low temperature. ligitek electronics co.,ltd. property of ligitek only this test is conducted for the purpose of detemining the resistance of a part in electrical and themal stressed. the purpose of this is the resistance of the device which is laid under condition of high temperature for hours. the purpose of this is the resistance of the device which is laid under condition of low temperature for hours. description part no. LPG3333-PF
|
